Proposed Codes

current status of the coding for the WorldSID dummy
Post Reply
DiVe
Posts: 349
Joined: Tue Apr 24, 2007 9:14 am
Company: IAT mbh
Location: IAT Berlin - Germany
Contact:

Proposed Codes

Post by DiVe »

Please find enclosed the current table of ISO Codes for WorldSID 50th measurements.
The Fine Location 3 Coding for the WorldSID has been defined as "WS". For the upcomming 5th percentile the Fine Location 3 Code will be "WF.
WORLDSID_ISO-Codes_Preliminary_V0_2.xls
(44.5 KiB) Downloaded 923 times
Comments and extensions are welcome.

The Coding is intended to be added in the database for V 2.x or may also in an earlier Release (V 1.6?).

Dirk Vetter
DiVe
Posts: 349
Joined: Tue Apr 24, 2007 9:14 am
Company: IAT mbh
Location: IAT Berlin - Germany
Contact:

Re: Proposed Codes

Post by DiVe »

.. just a small update on the coding based on some comments from Daimler ..
All changes highlighted by color.
Attachments
WORLDSID_ISO-Codes_Preliminary_V0_4.xls
(44.5 KiB) Downloaded 716 times
cgehre
Posts: 1
Joined: Mon Oct 01, 2012 10:49 am
Company: PDB - Partnership for Dummy Technology and Biomechanics

Re: Proposed Codes

Post by cgehre »

There are two systems available to measure the rib deflection of the WS50% - IR-TRACC 1D (current solution) and IR-TRACC 2D (probably future solution). The 1D system measures the deflection between rib bracket and spine box. The 2D system measures the deflection between rib bracket and a moving point in front of the spine box, and the sensor’s rotation about the vertical axis. Both systems are measuring only the same deflection under pure lateral rib deflection (rare condition) --> see attachement

Therefore, it would be helpful to use different ISO codes for both systems to distinguish between measurements of the 1D and the 2D system.

Proposal:
1D system: current code *DSY*; correct code would be *DSR*, but should not be changed because the system could become obsolete
2D system: proposal: *DS0* (*DSX*, *DSY*, *DSZ*, and *DSR* could be calculated if two additional angles are available: rotation of the sensor about z and x)

Christian Gehre
Attachments
comparison_end2.jpg
comparison_end2.jpg (17.6 KiB) Viewed 13433 times
comparison_start2.jpg
comparison_start2.jpg (19.02 KiB) Viewed 13433 times
xyz.gif
xyz.gif (445.27 KiB) Viewed 13433 times
User avatar
Paul Wellicome
Posts: 176
Joined: Mon Apr 23, 2007 2:20 pm
Company: HORIBA MIRA Ltd
Location: HORIBA MIRA Ltd, England

Re: Proposed Codes: Shoulder

Post by Paul Wellicome »

In order to be consistent with how ISO/WD 15830-4 references the locations on the shoulder, would it not make more sense in the WS to put the acceleration and displacement on the shoulder rib rather than the shoulder? That is where the instrumentation is actually mounted. We’d then have

??SHRILE00WSACXB Shoulder Rib Left Acceleration X
??SHRILE00WSACYB Shoulder Rib Left Acceleration Y
??SHRILE00WSACZB Shoulder Rib Left Acceleration Z
??SHRILE00WSDSYB Shoulder Rib Left Displacement Y
??SHLDLE00WSFOXB Shoulder Left Force X
??SHLDLE00WSFOYB Shoulder Left Force Y
??SHLDLE00WSFOZB Shoulder Left Force Z
??SHRIRI00WSACXB Shoulder Right Acceleration X
??SHRIRI00WSACYB Shoulder Right Acceleration Y
??SHRIRI00WSACZB Shoulder Right Acceleration Z
??SHRIRI00WSDSYB Shoulder Right Displacement Y
??SHLDRI00WSFOXB Shoulder Right Force X
??SHLDRI00WSFOYB Shoulder Right Force Y
??SHLDRI00WSFOZB Shoulder Right Force Z
Paul.
gieschef
Posts: 11
Joined: Thu Dec 16, 2010 2:04 pm
Company: TRW Automotive GmbH
Location: TRW Automotive GmbH Alfdorf/Germany

Re: Proposed Codes

Post by gieschef »

On my opinion the 2D-IR-TRACC displacements should be defined with direction '2' (lateral) as this is what is really measured. The X and Y channels are then calculated from measured displacement and the angle for each IR-TRACC.
This is the way we have implemented 2D-IR-TRACCs already in the past.

If you agree on that i would suggest to change the proposed codes accordingly.

Best regards,
Frank Giesche
derpmann
Posts: 460
Joined: Tue Apr 24, 2007 5:32 am
Location: Volkswagen AG, Wolfsburg - Germany

Re: Proposed Codes

Post by derpmann »

for the WS dummy figure please see http://www.iso-mme.org/forum/viewtopic.php?f=113&t=381

for the chest deflection figure please see http://www.iso-mme.org/forum/viewforum.php?f=122

Regards

Peter
gieschef
Posts: 11
Joined: Thu Dec 16, 2010 2:04 pm
Company: TRW Automotive GmbH
Location: TRW Automotive GmbH Alfdorf/Germany

Re: Proposed Codes

Post by gieschef »

Hello ,
are there already proposals for the several Ribeye channels available ?

At least a subset of the overall channels should be integrated to standard WS measurement, but already for front, middle and rear we have no finelocation left to encode this.

Thank you for a hint and best regards,

Frank
Post Reply

Return to “Codes for WorldSID”